| Date |
Fixed |
|
| 26 Mar 06 |
|
Remove exhaust port plugs & tighten exhaust connector links. |
| 27 Aug 02 |
|
Prop – Inspect blades in spinner area. 2 small nicks, one on face of blade 96 and one on back of blade 95. |
| 27 Aug 02 |
|
Prop – Polish and repaint the 2 small nicks above. |
|
|
Front Seat – Make seat riser to put under parachute? Maybe not needed. Check after purchasing a helmet |
| 07 Mar 07 |
|
Install ELT antenna |
| 08 Oct 07 |
|
Put spiral wrap on Hall Effect Sensor wires |
| 24 Jul 07 |
|
Review FT data recording script. Fix list of snags identified at top of script. |
| 06 Sep 07 |
|
Install front seat belts |
| 07 Jul 05 |
|
Install TVS on defrost fan |
| 09 Aug 06 |
|
Oil separator – install breather line on exit |
| 02 Dec 06 |
|
Fabricate computer hold down tray |
| 02 Dec 06 |
|
Finish engine cooling plenum |
| 27 Jan 07 |
|
Install safety wire on baffle cylinder wrap-arounds |
| 26 Feb 07 |
|
Secure wiring ahead of FW |
| 06 May 07 |
|
Install EI plug wires |
| 12 Aug 07 |
|
Put heat shield foil inside cowling bottom. |
| 20 Aug 07 |
|
fill and bleed brake system |
| 08 Oct 07 |
|
Install wing walk anti-slip |
| 19 Jan 08 |
|
Retorque tail wheel axle bolt, in warmer weather, after greasing it. |
| 17 Feb 08 |
|
Joggle IB end of lower flap skin |
| 18 Apr 06 |
|
Flaps – Add rivets on lower surface to join upper and lower skins at inboard end, if required. |
| 17 Feb 08 |
|
Install bolts at top of flap pushrods |
| 17 Feb 08 |
|
Reinstall COM 1 antenna |
| 17 Feb 08 |
|
Install new Xpdr antenna |
| 18 Feb 08 |
|
Install pitot heat CB before final inspection |
| 22 Mar 08 |
|
COM 2 functional test |
| 22 Mar 08 |
|
Install screws in L wing tip (after COM 2 functional test) |
| 11 Apr 08 |
|
Put edge guard on LG box brace @ Narco coax area |
| 13 Apr 08 |
|
Check magneto timing |
| 13 Apr 08 |
|
Fill divot in under-wing NACA scoop. |
| 27 Apr 08 |
|
Replace 2 valve covers |
| 27 Apr 08 |
|
Pull two cylinders and inspect inside engine |
| 27 Apr 08 |
|
Weight and Balance |
| 01 Feb 02 |
|
EI – Time EI and torque the bolts holding the sender to the accessory case |
| 17 Jun 01 |
|
FI Servo - Remove plastic covering the intake |
| 27 Jan 07 |
|
Retrieve red “straw” from fogging spray can from front left cylinder |
| 30 Mar 08 |
|
Put break-in oil in engine and pre-oil it |
| 16 Feb 02 |
|
Starter Solenoid – Tighten nuts attaching the cables |
| 27 Apr 08 |
|
Full power engine run |
| 27 Apr 08 |
|
Final inspection |
| 27 Apr 08 |
|
Install cockpit floor |
